ASP Nail Builder Gel - Cashmere 9ml

ASP Nail Builder Gel is a calcium enriched builder gel, in an easy brush on formula. It applies like a soak off gel polish but works like a hard gel. LED/UV self-levelling lightweight formula allows you to reinforce, build and extend a natural nail.

Always start with freshly prepped and manicured nails. This will help to ensure the best adhesion to your manicure.

Builder on natural nails:

1.   Dehydrate all ten nails using ASP 2 in 1 Dehydrator Cleansing Wipe.
2.   Apply ASP bonder, on the entire natural nail to help product adhere to natural nail.
3.   Start by applying a thin coat of ASP Builder Gel one hand at a time, being sure to seal the Free Edge of each Nail. Cure this hand for 30 seconds under LED or for 2 minutes under a UV Lamp. Repeat on the opposite hand.
4.   PRO TIP: If the nails have ridges apply the Base parallel to the side walls of the natural nail to fill the ridges.
5.   Apply a second coat of ASP Builder Gel onto the entire nail. CURE for 30 seconds under LED or 2 minutes under UV.
6.   To remove the sticky layer use ASP 2 in 1 Dehydrator Cleansing Wipe on a lint free wipe.
7.   Can be worn alone or topped with Nail Lacquer or Soak off Gel.

Builder using full coverage nails:

1.   Size the full coverage nail onto your natural nail bed. Do all ten fingers so they are ready for application.
2.   Using the sanding stick, buff the underside contact area of the full coverage tip to remove the smoothness. Clean off dust with a lint free wipe.
3.   Working one nail at a time - start by applying a thin layer of ASP Nail Builder Curing Gel to the entire natural nail and flash cure for 10 seconds under a LED lamp.
4.   Apply ASP Nail Builder Curing Gel on the underside filed area of the full coverage nail.
5.   Apply Full Coverage tip onto the natural nail at a 45 degree angle to press out any air bubbles and press into place until the gel levels and fills up the natural nail.*If necessary clean off any excess gel that may come out with a birchwood stick.
6.   Holding the tip in place, flash cure for 10 seconds under a LED lamp. It’s important to hold the nail here, before allowing it to fully cure, so that no bubbles form. Cure under an LED lamp for 1 minute or 2 under UV.
7.   Remove any excess gel around the side of the nail by filing gently. Style as desired, Use your favorite ASP Longwear Polish, ASP Gel Polish or brand of your choice.

Easy removal:

1.   Using a 180-grit file 20% of the existing product.
2.   Saturate a cotton ball with Acetone, wrapping onto the nail with a small square of foil.
3.   Soak-off time will vary between 15-20 minutes.
4.   Using the Soak-Off Remover tool, gently glide any remaining product off the nail.

DI-HEMA Trimethylhexyl Dicarbamate, Isobornyl Methacrylate, HEMA, Hydroxypropyl Methacrylate, Ethyl Trimethylbenzoyl Phenylphosphinate, Hydroxycyclohexyl Phenyl Ketone, Acrylic Acid, Calcium Pantothenate, Ethyl Acetate, Butyl Acetate, PEG-9 Dimethacrylate, Isopropyl Alcohol, Trimethylbenzoyl Diphenylphosphine Oxide, +/-: CI 60725 (Violet 2), Cl 77891 (Titanium Dioxide), CI 19140 (Yellow 5), CI 15850 (Red 7), CI 77499 (Iron Oxides).

Flammable, Keep away from heat, sparks and flames. Use in well ventilated area. Do not take internally. Avoid contact with eyes and skin. May cause allergic reaction. KEEP OUT OF REACH OF CHILDREN.